Gutter guide
The gutter glossary.
The words and sizes you will see on a quote or hear on the roof, in plain English. Search the glossary or scan the sizes table.

The sizes
Eight terms worth knowing.
Profiles, sizes, pitch and the way gutters are measured.
| Term | Common sizes | What it means |
|---|---|---|
| K-style gutter | 5 and 6 inch | The most common profile, with a flat back and a decorative front. Six inch carries about half again more water than five. |
| Half-round gutter | 5 and 6 inch | A rounded trough on brackets, common on historic homes. It carries a little less than a K-style of the same width. |
| Downspout | 2 by 3, 3 by 4, round | The pipe that carries water down. A 3 by 4 downspout carries far more than a 2 by 3. |
| Pitch | About 1/4 inch per 10 feet | The slight fall of a gutter toward its downspout. Too little holds water, too much looks wrong. |
| Hanger spacing | About 24 to 36 inches | How far apart the supports are. Closer spacing holds more weight in leaves and ice. |
| Roof pitch | Rise over 12 inches of run | How steep the roof is. Steeper roofs shed water faster and can overshoot some guards. |
| Roof footprint | Square feet | The area of the roof that drains into a run of gutter, measured flat. It drives how much water arrives. |
| Linear foot | Feet of gutter | How gutter and guards are priced and measured: the length of the run, not the area. |
The glossary
Terms you will hear on site.
Plain-English meanings for words that come up in gutter estimates and on the job.
- Apron flashing
- A bent metal strip that tucks under the shingles and laps over the back edge of the gutter so water cannot run behind it.
- Bracket hanger
- A decorative support that holds a half-round gutter away from the fascia.
- Downspout
- The pipe that carries water from the gutter down to the ground or a drain.
- Drip edge
- Metal at the roof edge that sends water off the roof and into the gutter instead of behind it.
- Elbow
- A bend in a downspout, used to turn it around the eave or out at the bottom.
- End cap
- The piece that closes the end of a gutter run. It is sealed and a common spot for leaks.
- Extension
- A pipe or flexible hose that carries downspout water farther from the foundation.
- Fascia
- The trim board along the roof edge that the gutter attaches to.
- First flush diverter
- A device that sends the first dirty runoff of a rain away from a rain tank.
- Gutter apron
- Another name for apron flashing.
- Gutter guard
- A cover, screen, mesh or hood that keeps leaves and debris out of a gutter while letting water in.
- Hanger
- The bracket or strap that holds the gutter to the fascia and sets its pitch.
- Hood guard
- A solid cover with a rounded nose that water clings to and turns into the gutter.
- K-style
- The most common gutter profile, with a flat back and a decorative front.
- Linear foot
- A foot of length. Gutters and guards are measured and priced by linear foot.
- Mastic
- A thick sealant used on seams and joints.
- Micro-mesh
- A very fine screen used in gutter guards to block needles, seeds and grit.
- Miter
- The corner joint where two gutter runs meet at an angle.
- Outlet
- The opening in the bottom of a gutter where the downspout connects.
- Overshoot
- Water that skips over a guard or gutter in a heavy downpour instead of dropping in.
- Pitch
- The slight fall of a gutter toward its downspout, usually about a quarter inch per ten feet.
- Reverse curve
- A guard shape that lets water follow the curve into the gutter while leaves slide off.
- Seamless gutter
- A gutter formed from one long piece of metal, with joints only at corners and outlets.
- Soffit
- The panel on the underside of the roof overhang.
- Splash block
- A shaped block under a downspout that slows and spreads the water.
- Valley
- The inside corner where two roof planes meet. It concentrates water into a smaller stream.
No term matches that search. Call us and we will explain it.
Not sure what a quote means?
Send it to us and we will walk through it with you in plain words.
